Repair Of Miele Washing Machines
Repair of Miele washing machines at home in New York with an official warranty for work and spare parts.
Services Of The Service Center:
- Post-warranty repair of washing machines in New York (Manhattan, Brooklyn) with the departure of the master to the place of installation of the equipment. Including urgent repairs.
- Installation, configuration, connection and maintenance (including error reset) of new and used washing machines.
- Maintenance of Mile washing machines (replacement of filters, cuffs, descaling, etc.), including warranty extension. We consider it necessary to note that timely prevention reduces the likelihood of breakage, as well as increases the service life of the washing machine.
- Sale of spare parts and consumables for washing machines of all types (the entire model range, including discontinued ones). You can buy the necessary components from us on order and with delivery.
Advantages of our service:
-
Own repair shop
You can call a specialist at home or bring a washing machine to our service yourself.
-
Reasonable prices and flexible discount system
We have really inexpensive repairs and constant discounts on standard repair and maintenance work. See the section "Discounts".
-
Specialist check-out and diagnostics 125$
Departure of the repair team at the installation site of the washing machine New York (Manhattan, Brooklyn) 125 $.
-
Factory warranty
The factory warranty of the Miele Washing Machine Service Center is up to 5 years. See the section "Guarantees".
-
Support Hotline
Consultations on the repair and operation of Miele washing machines in 24x7 mode.
The main faults:
-
Does not turn on (does not work)
The main reasons why the washing machine does not start (there is no indication on the scoreboard):
- Wiring malfunction or lack of mains voltage.
- A defect (breakdown) of the power button.
- Malfunction of the control unit (controller).
If there is an indication, but there is no washing program:
- Incorrectly selected washing program.
- Lack of water supply (pressure at the inlet pipe).
- A malfunction of the intake valve.
Couldn't handle it with your own hands? Call a Technician
-
Does not turn off
If the washing machine fails, first of all pay attention to the error code message, this information is often enough for correct diagnosis.
Typical reasons in this case are as follows:
- Strong surges or power outages.
- Malfunction of the control unit (software controller).
- Malfunction or improper operation of the filling valve.
Didn't you manage on your own? Call a Technician
-
Does not collect water
The main reasons why the Miele washing machine does not collect water:
- Lack of water supply (pressure at the inlet pipe).
- Clogging of the intake strainer.
- A malfunction of the intake valve.
- Malfunction of the control unit (software controller).
- Malfunction of the water level sensor (pressostat) or its connection.
- Malfunction of the hatch lock.
Didn't you manage on your own? Call a Technician
-
Does not drain water
The main reasons why the washing machine does not drain the water:
- Blockage on the drain line: hose, siphon, drain filter.
- Malfunction of the water level sensor of the pressostat or its connection circuits.
- Malfunction of the pump or its power supply circuits.
- Malfunction of the control unit (software controller).
Couldn't fix the washing machine with your own hands? Call a Technician
-
Does not heat the water
The main reasons why the Mile washing machine does not heat the water:
- Incorrect operation mode is set.
- Thermostat malfunction.
- Malfunction of the control unit (software controller).
- Malfunction of the heating element or its power supply circuits.
Couldn't fix the washing machine with your own hands? Call a Technician
-
The drum is not spinning
If the drum of the washing machine is jammed (it is impossible to turn it by hand), then possible causes of the problem:
- A foreign body between the drum and the tank.
- A defect (destruction) of the bearing.
If the drum does not rotate during operation, then the main malfunctions:
- The malfunction of the electric motor, as one of the common causes, is the wear of the brushes.
- A defect (breakage) of the drive belt.
- Malfunction of the control unit (software controller).
Couldn't fix the problem on your own? Call a Technician
-
Extraneous sounds during operation ("knocking", "buzzing", etc.)
The main causes of extraneous noise during operation of the washing machine:
- Foreign objects in the mechanism of rotation of the drum.
- Failure of the tank counterweight attachment.
- The defect of the shock absorption mechanism is the shock absorber itself, the spring or the mount.
- Bearing wear.
- Vibration of the drum pulley, most often due to loose fastening. When working, there is a characteristic crackle.
Breakdowns, as a result of which extraneous sounds appear during operation of the washing machine, require urgent repair.
Couldn't fix the problem on your own? Call a Technician
-
Leaking (triggering WaterProof)
The main reasons for the leakproofness of washing machines are Miles:
- Pump malfunction.
- Failure of the sealing gland.
- There is a blockage on the water supply line to the powder tray or the tray itself.
- A defect in the manhole cuff.
- A defect in the inner pipe.
Couldn't fix the equipment with your own hands? Call a Technician
-
Error message
Find Miele Washing Machine Error Codes or call our Service Center. Call a Technician
Main repair work:
-
Replacement of buttons, switches
(from 960$)
-
Replacing the door handle
(from 1120$)
-
Replacement of the manhole cuff
(from 1360$)
-
Replace Hatch lock device
(from 1600$)
-
Replacing the drive belt
(from 1360$)
-
Replacing the drain pump
(from 1920$)
-
Replacing the heating element
(from 1680$)
-
Replacement of shock absorbers
(from 2000$)
-
Repair of the crosspiece
(from 2080$)
-
Replacement of bearings
(from 1840$)
-
Complete assembly/disassembly
(from 2240$)
-
Repair of the control module
(40% of the cost of a new one)
Error codes:
-
The main error codes of Miele washing machines
Error code Cause, troubleshooting F1 Error of the water temperature sensor (NTC sensor): sensor malfunction or short circuit.
After registering this malfunction, the heating is not activated, the program is interrupted prematurely with the display of the specified error.
To solve the problem (error 01):
- Check the sensor (R30).
- Check the connectors.
- If the problem persists, contact the Miele Service Center. Replacement of the corresponding sensor or repair of its connection circuits is required.
F2 Error of the water temperature sensor (NTC sensor): disconnection (disconnection of contacts) of the sensor.
After registering this malfunction, the heating is not activated, the program is interrupted prematurely with the display of the specified error.
To solve the problem (error 02):
- Check the sensor (R30).
- Check the connectors.
- If the problem persists, contact the Miele Service Center. Replacement of the corresponding sensor or repair of its connection circuits is required.
F3 Error of the air temperature sensor (NTC sensor of the fan) of the washing machine: malfunction of the sensor or its short circuit.
To solve the problem, see the description of errors 01, 02.
F4 Error of the air temperature sensor (NTC sensor of the fan) of the washing machine: disconnection (opening of contacts) of the sensor.
To solve the problem, see the description of errors 01, 02.
F5, F16 Excessive foaming.
After registering this malfunction, in order to reduce foaming, the washing machine resets (heating is turned off in some models), displays the specified error and "Dosing check" (flashing indication).
Error 05 is fixed only in the "Coarse wash" mode (Cotton/Linen) and "Easy care" during the main wash.
To solve the problem, try using a smaller amount of detergent.
F6, F10 Water supply error.
During a certain time, an insufficient filling rate of the tank is recorded (error 06) or a complete lack of water supply (error 10).
After registering this malfunction, the drainage pump starts, the indicated error is displayed and the flashing indication "Check inlet" or "Check supply" is displayed.
To solve the problem:
- Check the water pressure in the inlet pipe.
- Check the intake valve.
- Check the water level sensor.
- Check the intake valve filter (possible blockage).
- Check the control unit (possible malfunction or malfunction).
F7, F11 Water drain error.
During a certain period of time, insufficient water discharge rate is recorded (error 07) or complete absence of discharge (error 11).
After registering this malfunction, the program execution is suspended, the specified error and the "Verification procedure" (flashing indication) are displayed.
To solve the problem:
- Check the drain hose (it may be clogged or bent).
- Check the drain filter (possible blockage).
- Check the drain pump (possible malfunction or blockage by a foreign object).
- Check the water pressure switch.
- Check the control unit (possible malfunction or malfunction).
F8 Spin error.
Insufficient speed of rotation of the drum or complete absence of rotation is recorded.
To solve the problem:
- Check the possibility of free rotation of the drum (it is possible to block it with a foreign object).
- Check the tacho generator.
- Check the drive motor (there may be a malfunction of the motor itself or its power supply circuits).
In some cases, error 08 occurs when the washing machine is overloaded.
F9, F41 Control unit error.
An error reading the permanent EEPROM memory is registered.
To solve the problem, try to completely disconnect the washing machine from the mains for a few minutes, and then turn it back on. If the error persists, the controller needs to be repaired at the component level (replacing or reprogramming the EEPROM chip).
F15 Water supply error.
The hot water supply at the inlet pipe is recorded. +-
F19 Water supply error.
A malfunction of the flow meter has been detected: obviously incorrect data is received from the flow sensor, or the data is not received at all.
After registering this malfunction, the program is suspended, the drainage pump is started and error 19 is displayed.
To solve the problem, check the flow sensor (it may malfunction or be blocked by a foreign object).
F20 Water heating error.
Insufficient water heating rate or complete absence of heating is recorded.
To solve the problem (error 20):
- Check the temperature sensor.
- Check the heating element relay (there may be a malfunction of the relay or its connection circuits).
- Check the heating element
F29 Air heating error (washing and drying machines).
Insufficient air heating rate or complete absence of heating is recorded.
The solution to the problem is similar to the one described above (see "error 20").
F34 Door closing error.
The automatic lock of the hatch door does not work. The program does not start and error 34 is displayed.
To solve the problem:
- Check the possibility of closing the door (it may be blocked by a foreign object).
- Check the serviceability of the locking device.
- Check the control unit (possible malfunction or malfunction). In some cases, it is enough to completely disconnect the washing machine from the electrical network for a few minutes, and then turn it on again.
F35 An error opening the door.
Unlocking the hatch door does not work.
To solve the problem:
- Try to completely disconnect the washing machine from the mains for a few minutes, and then turn it back on.
- Check the locking device (UBL), its malfunction or jamming is possible.
F37 Alignment error.
It is required to install a washing machine by level.
F39 Control unit error.
An error is registered on the communication line control unit - power unit.
To solve the problem, try to completely disconnect the washing machine from the mains for a few minutes, and then turn it back on. If the error persists, repair of the controller or power unit at the component level is required.
Error 39 also appears when the controller and the power unit are incompatible.
F43 Compatibility error.
The control unit does not recognize one of the washing machine modules. Error 43 sometimes occurs when the blocks are incorrectly replaced during repair.
F45 Control unit error.
An error reading Flash memory is registered.
To solve the problem, try to completely disconnect the washing machine from the mains for a few minutes, and then turn it back on. If error 45 has not disappeared, the controller needs to be repaired at the component level (usually replacing the Flash memory chip).
F46 Communication error with the display unit.
A malfunction or incorrect connection of the display unit (LCD display) is registered.
To solve the problem (error 46):
- Check the integrity of the display connection cable.
- Check the LCD display (possible malfunction or moisture ingress).
F47, F49 Communication error on the BAE/STD interface.
The error connecting the display module is registered.
F50 Drum drive error.
Insufficient speed of rotation of the drum or complete absence of rotation is recorded.
To solve the problem (error 50):
- Check the possibility of rotation of the drum (it is possible to block it with a foreign object).
- Check the loading of the washing machine (excessive loading is possible).
- Check the serviceability of the drive motor and its power supply circuits.
F51 Error of the pressure sensor (pressostat).
A pressostat error is registered: obviously incorrect data is received from the pressure sensor, or the data is not received at all.
To solve the problem, diagnostics of the sensor (by replacing it with a known serviceable one) and its connection circuits are required.
F53 Tachogenerator error.
A tachogenerator error is registered: obviously incorrect data is received from the rotation speed sensor, or the data is not received at all.
To solve the problem, diagnostics of the sensor (by replacing it with a known serviceable one) and its connection circuits are required.
F55 The error of the drying timer of the washing machine: an excess of the maximum operating time of the drying mode is registered.
To solve the problem (error 55):
- Completely disconnect the washing machine from the mains for a few minutes, and then turn it on again.
- Check the drying timer.
- Check the mode switching relay.
F56 Tacho generator error.
The rotation speed of the drum is too low in the spin mode.
To solve the problem (error 56):
- Check the possibility of rotation of the drum (it is possible to block it with a foreign object).
- Check the loading of the washing machine (excessive loading is possible).
- Check the serviceability of the power supply circuits of the drive motor.
- Check the tacho generator.
F62 DWS/B97 program selector error.
F63 A flow allocation error. A flow allocation error.
An error is registered in the operation of the flow control unit.
To solve the problem (error 63):
- Check the amount of detergents (excessive loading is possible).
- Check the dispenser (possible blockage).
- Check the flow control unit.
F64 Flow sensor error. Flow sensor error.
To solve the problem, diagnostics of the sensor (by replacing it with a known serviceable one) and its connection circuits are required.
F65 Error in the drum illumination.
To solve the problem (error 65):
- Check the backlight lamp.
- Check the connection circuits of the backlight lamp (contacts).
F69 Circulation pump error.
To solve the problem (error 69):
- Check the circulation pump.
- Check the power circuits of the circulation pump connection.
F81 Washing Machine Drying Heating Error: there is no heating.
To solve the problem (error 81):
- Check the heating element.
- Check the heating drying relay.
F83 The error of heating the drying of the washing machine: an excess of the maximum drying temperature is recorded.
To solve the problem (error 83):
- Check the steam-thermal drying unit.
- Check the heating element relay for drying.
F92 Humidity sensor error.
For a long time, increased humidity is recorded inside the washing machine (some models have a flashing "Hygiene information" indication).
To solve the problem (error 92):
- Check the humidity sensor.
- Eliminate the source of increased moisture.
F93 The relay error of the additional module.
Check the relay, replace it if necessary.
F96 An error in the supply of alternative water supply.
F100, F101 Communication error with IK6.
A communication malfunction with IK6 is registered.
F102 The "smart home" error.
A connection error with the smart home is registered.
To solve the problem (error 102), check the Wi-Fi connection.
F103 The "smart home" error.
A hardware compatibility error or connection method error is logged.
F104 Power supply error.
A noticeable deviation in the parameters of the supply network is registered.
F131 EZL 265 block error.
A malfunction of the EZL 265 control unit is registered.
F138, F220 The error is WaterProof.
A water leak is registered (the AquaStop float sensor has been activated).
After registering this malfunction, the leak protection system is triggered: the program is suspended, the drainage pump is started and the corresponding error is displayed.
To solve the problem (error 138, 220):
Shut off the water supply to the washing machine and disconnect it from the mains.
- Check for water in the tray (drain if available).
- Check the float sensor (possible malfunction or sticking).
- Check the pallet horizon (bending or deformation may occur during transportation).
- If there is water in the pan, visually check the tightness of the connections and the integrity of the hoses.
- Check the detergent dispenser (possible blockage).
F139 WPS distributor error.
A fault is registered in the WPS distributor.
F140 Dispenser error.
A malfunction (blockage) of the dispenser is registered.
F211 - F214 TwinDos error (for devices with DOS Auto Dispenser).
A malfunction or malfunction of the detergent dispenser is registered.
To solve the problem (TwinDos):
- Check the detergent dispenser.
- Check the temperature sensor and its connection circuits.
Determine the cause of the breakdown and the full cost of repair:
Question and Answer:
-
Hello. What causes the washing machine to have the F20 error? At the same time, the washing process goes on as usual. The washing machine model is WT2670.
Error 20 is a water heating error: insufficient heating speed or no heating at all.
All possible reasons for this error, one way or another, are related to the heating element. Most often, there is a malfunction or scale contamination. Apparently, in your case, the second option takes place.
Visually check the condition of the heating element, and in case of noticeable salt deposits, clean the washing machine from scale according to the instructions.
-
Can you tell me, please, why error 63 may sometimes appear on the washing machine? Thank you in advance.
Hello. Error F63 is a thread allocator error. It usually arises about the cause of the malfunction of this distributor itself, but in some washing machines, for example, it may appear due to excess detergent or clogging of the dispenser.
Write the model of your washing machine in the reply message, and we will help you deal with the problem.
-
Errors F138, F220, WaterProof for Miele washing machines. What to do?
These errors indicate a problem with a leakproofness violation: the float sensor in the pallet (Aquastop) is triggered. To solve the problem, it is necessary to turn off the washing machine, disconnect it from the mains and visually check the presence of water in the tray.
- If there is water, it must be drained, then the cause of the leak must be identified and eliminated.
- In the absence of water, check the serviceability of the float sensor itself: it may "stick" or malfunction.
Reviews:
-
Profitably.
I decided to write a review, because, firstly, I was pleasantly pleased with the repair price, and secondly, upon arrival, we purchased accessories for our washing machine, and also at an attractive price.
Our old WT2670 is now working like new.
(12.22.2023)Kingsley, manhattan (NY).
-
Спасибо Антону.
Good day. I wanted to share my experience of getting to know this service. I made an urgent check-out, because at the end of the washing, my washing machine left a huge puddle in the laundry room.
When making an application, the time of the master's arrival was set for 7:15 a.m. The team arrived on time and eliminated everything. Thanks to Master Anton, I recommend it.
(12.09.2023)Bentley Wright, Manhattan (NY).
-
Good service and affordable prices.
I turned to the repair of the washing machine W1714 (it rattled strongly when pressing), the problem was fixed within an hour. The specialist gave appropriate recommendations for further operation.
Thank you.
(11.07.2023)Kevin Garcia, Lower Manhattan (NY).
Any other questions? Order a callback. The response time is less than a minute.