Repair Of Miele Ironing Systems
Repair of all types of Miele ironing systems and ironing rollers in New York with a manufacturer's warranty for work and spare parts.
Services Of The Service Center:
- Post-warranty repair of Mile ironing systems in New York (Manhattan, Brooklyn) with departure at the place of installation of the equipment
- Installation, configuration, connection and adaptation of new and used ironing systems.
- Maintenance (prevention) of Miele ironing equipment (cleaning, decalcification, etc.), including the extension of the warranty for Miele Professional rollers.
- Sale of spare parts for Miele ironing systems from a warehouse in New York, including on order and with delivery.
Advantages of our service:
-
Own repair shop
We have our own repair shop and modern diagnostic equipment, as a result, we make repairs of any complexity at reasonable prices and in the shortest possible time.
-
Repair on the day of the request
In the vast majority of cases, the repair of the ironing system is carried out in one trip when calling the master at home, or within a few hours when contacting the repair shop.
-
Repair of ironing equipment of all types
We repair any Miele ironing equipment:
- Ironing systems (B2847, B3847 Fashionmaster, etc.).
- Industrial ironing rollers (HM 21-100, HM 21-140, etc.).
- Irons and steam generators.
-
Check-out and diagnostics 125$
- The cost of troubleshooting the Miele ironing system: $ 125 (included in the repair cost).
- Departure to the place of installation of ironing equipment within New York (Manhattan, Brooklyn)
-
Brand Warranty
The official warranty of the service center for the repair of Miele ironing systems is up to 5 years. See the section "Guarantees".
Main faults:
-
Does not heat the iron
If the iron itself is in good condition, then the main causes of this malfunction are as follows:
- A defect in the power button.
- Failure of the thermal fuse.
- Malfunction of the thermostat.
-
No steam is formed
The main reasons for the lack of steam supply in the Miele ironing system:
- Boiler heating element malfunction.
- Failure of the pressure switch or solenoid valve.
- A defect in the steam supply button on the iron.
- Malfunction of the pump or its power supply circuits.
-
Steam is constantly flowing
The main reasons why steam is constantly running in the ironing machine:
- A defect in the steam supply button on the iron.
- Failure of the solenoid valve.
-
Low steam pressure
The main causes of low steam pressure in the ironing machine:
- Malfunction of the feed pump.
- Scale (dirt) on the iron.
-
Steam from the emergency valve
The main reasons for the operation of the emergency valve:
- Malfunction of the cover of the emergency valve itself.
- Failure of the pressure regulator.
-
Incorrect water level indication
The main reasons for the erroneous indication of the water level in Miele ironing machines:
- Thermostat malfunction.
- Failure of the capillary sensor.
- In rare cases, deformation of the heating element.
-
Leaks from under the steam generator body
The main reasons for the leakproofness of ironing machines:
- The sealing is broken (most often – a defect in the heating element gasket).
- Failure of the pressure switch.
- Malfunction of the solenoid valve.
-
Error message
See Error codes of Miele ironing systems or call our Service Center. Call a Technician
Main repair work:
-
Replacement of buttons, switches
(from 900$)
-
Repair (replacement) of the power cord
(from 600$)
-
Sensor replacement (with diagnostics)
(from 1400$)
-
Replacement of the electric valve
(from 1200$)
-
Replacing the control unit
(from 2400$)
-
Iron repair
(from 1800$)
-
Complete cleaning of the boiler
(from 2200$)
-
Pump replacement
(from 1800$)
Error codes:
-
The main error codes and service messages of Miele ironing systems
Error code Cause, troubleshooting F38 Power supply unit error.
A malfunction of the power supply is registered.
To solve the problem (error 38):
- Disconnect the ironing system from the mains for half an hour, and then turn it on again.
- If the error persists, diagnostics and repair of the power supply at the component level are required.
F44 Iron error.
A malfunction of the connection with the iron is registered.
To solve the problem (error 44):
- Check the connecting cord.
F45, LNG Steam generator error.
A steam supply error is registered.
To solve the problem (error 45):
- Check the steam generator.
F47 Control unit error.
To solve the problem (error 47):
- Disconnect the ironing system from the mains for half an hour, and then turn it on again.
- If the error persists, diagnostics and repair of the controller at the component level are required.
"Auth. close. drain. vl." The steam generator drain is open.
When the ironing system was turned on, the steam generator drain was open. When this message appears, the drain is automatically closed.
«Memory error On off.» Memory reading error.
An error is registered at the initialization stage of the ironing system.
To solve the problem:
- Turn off the ironing system with the on button, and then turn it on again.
- Perform the initial setup of the ironing system (see the chapter "First commissioning").
- If the error persists, contact the Miele Service Center.
«Turn off the power supply» Control unit error.
An error is registered at the initialization stage of the ironing system.
To solve the problem:
- Disconnect the ironing system from the mains for a few minutes, and then turn it on again.
- If the error persists, contact the Miele Service Center.
«The problem is switching On/off.» Water supply error.
An error is registered at the stage of pouring water into the steam generator.
To solve the problem:
- Turn off the ironing system with the on button, and then turn it on again. After cooling (it may take several hours), the flushing process will be started and an attempt will be made to fix the problem on its own.
- Next, remove the pull-out container for draining water (if the corresponding message appears on the display).
- Pour out the remaining water from the pull-out container and dry it.
- Insert the water drain container back into the base (before fixing).
- Если ошибка не исчезла, обратитесь в Сервисный Центр Miele.
"Malfunction of the pneumatic switch. On/Off" The error of the pneumatic switch.
To solve the problem:
- Turn off the ironing system with the on button, and then turn it on again.
- If the error persists, contact the Miele Service Center.
«The steam generator is overheated On/off.» Overheating of the steam generator.
To solve the problem:
- Turn off the ironing system with the on button, and then turn it on again.
- Start the descaling process.
- Set a higher level of water hardness (to prevent a similar situation from occurring in the future).
- If the error persists, contact the Miele Service Center.
«Steam generator is not heated On/off.» Ошибка парогенератора (нет нагрева).
To solve the problem:
- Turn off the ironing system with the on button, and then turn it on again.
- If the error persists, contact the Miele Service Center. Diagnostics and repair of the steam generator are required.
«Unlock the steam button» Steam button lock
The steam button was automatically locked and the iron was turned off due to a long break in use.
«Drain valve malfunction On/off.» Drain valve error.
An error in the operation of the drain valve is registered.
To solve the problem:
- Remove the water container and rinse it (including descaling, etc.)
- Refill the tank with water and install it back.
- Start the procedure for automatic diagnostics and troubleshooting.
- If the error persists, contact the Miele Service Center.
-
The main error codes of Miele Professional ironing rollers
Error code Cause, troubleshooting F0, F1, F2, F8, F20, F24, F25 Heating error
F39, F40, F41, F42, F43, F45, F47, F49 Control unit error.
To solve the problem:
- Disconnect the ironing roller from the electrical network for half an hour, and then turn it on again.
- If the error persists, diagnostics and repair of the controller at the component level are required.
F50, F53 A skating rink operation error.
F57 Fan error.
F61 Power supply unit error.
There is no voltage on the 12V (24V) bus.
F99 The device is locked.
F104, F120 Power supply unit error.
The voltage is too low.
F108 Compressor error.
F4500 - F4512 A control system error.
Determine the cause of the breakdown and the full cost of repair:
Question and Answer:
-
Hello, water has been dripping from the sole of the iron for some time. What could be the matter? Miele B2847 ironing system.
Possible causes of this malfunction:
- Failure of the heating elements of the sole. In this case, an iron replacement is required (repair is actually equivalent to replacement).
- Pump malfunction.
- Malfunction of the steam valve. Often, incorrect operation of the valve is a consequence of the formation of lime deposits (scale). In this case, it is sufficient to carry out a complete decalcification of the device (descaling).
-
The Miele ironing system shows "On/Off drain problems". What to do?
The reason for this message is a drain problem, which most often occurs due to the fact that the drain container is not recognized by the system. In this case, turn off the ironing system, then turn it on again and follow the instructions on the display:
- Take out the water drain container and fill it with fresh tap water.
- Insert a container filled with water into the base of the appliance.
- Pour out the remaining water from the pull-out container and dry it, then insert the empty container to drain the water into place.
Now the ironing system should be ready to work.
Reviews:
-
High-quality support.
I liked the good attitude towards the client: the polite and competent communication of the manager from the ironing systems repair department.
The error was fixed by phone, plus I received the necessary operating recommendations.
(12.28.2023)Trice, New York.
-
A real guarantee.
An important feature of this service is that the company correctly fulfills its warranty obligations. It's worth a lot now. For comparison, there was a bitter experience with the previous service center, where, under the guarantee of the arrival of a specialist, you had to wait more than 14 days.
Immediately, when our ironing system malfunctions, the service engineer arrived clearly within two days. Thank you very much! Mom told me to write a positive review about this company.
(12.05.2023)Randy Clark, 345 Park Avenue (NYC).
Any other questions? Order a callback. The response time is less than a minute.