Miele Dishwasher Repair
Repair of all types of Miele dishwashers in New York with a branded warranty on labor and parts.
Services Of The Service Center:
- Post-warranty repair of Miele dishwashers in New York with on-site visits (including home service).
- Installation, setup, connection, and adaptation of new and used dishwashers.
- Service maintenance (preventive maintenance) for Miele dishwashers (replacement of filters, seals, salt solution, cleaning of blockages, etc.), including warranty extension for appliances older than 2 years.
- Sale of spare parts and consumables for Miele dishwashers from our warehouse in New York, including delivery.
Advantages of our service:
-
Own repair shop
We have our own repair workshop, which allows you to request a specialist to your home or bring the dishwasher to our service center yourself.
-
Repair on the day of the request
In the vast majority of cases, dishwasher repairs are carried out in one visit when a technician is called to your home, or within a few hours when contacting our repair workshop.
-
Check-out and diagnostics $125
The cost of diagnosing dishwasher malfunctions for Miele machines is included in the repair cost.
A technician's visit to the installation site of the dishwasher within New York - 125$.
-
Brand Warranty
Official warranty from the Service Center for Miele dishwashers - up to 24 months. See the "Warranty" section.
Main faults:
-
Does not turn on (does not work)
Main reasons why the Miele dishwasher may not start:
- Break in the cord or a defective power plug.
- Clogging of the water inlet filter, resulting in insufficient pressure in the inlet hose.
- No water supply (pressure on the inlet hose).
- Malfunction of the control unit (software controller).
- Improperly closed door or lock malfunction.
-
Shuts down spontaneously
Main reasons why the Miele dishwasher may shut down spontaneously:
- Malfunction of the control unit (software controller).
- Clogging of the drain hose.
- Malfunctioning of the heating element (TEN) or its power supply circuits. The program stops because it is unable to heat the water to the required temperature.
- Malfunction of the circulation pump.
-
Does not open, does not close
Main reasons why problems with opening/closing the dishwasher occur:
- Door misalignment (often due to mechanical impact).
- Malfunction or displacement of the door lock.
- Defect or displacement of the sealing contour.
- Malfunction of the control unit (software controller) resulting in a lack of signal for locking the latch or releasing the lock.
-
Does not fill with water
Main reasons why the Miele dishwasher does not fill with water:
- No water supply (no pressure in the inlet hose).
- Defective pressure switch (level sensor) causing the controller not to understand the need to fill water.
- Leaks causing the "AquaStop" system to activate.
- Clogging in the inlet filter.
- Malfunctioning inlet valve.
- Malfunction of the control unit (software controller).
- Improperly closed door or malfunction of the door lock (door closer).
-
Does not drain water
Main reasons why the dishwasher doesn't drain water:
- The pump (drain pump) is clogged or has malfunctioned.
- A defective level sensor (pressure switch) causing the controller not to understand the need to drain water.
- Clogging in the drain filter.
-
Does not heat water
Main reasons for the lack of water heating in the Miele dishwasher:
- Incorrect temperature setting.
- Malfunction of the heating element (heater) or its power circuits (contact oxidation).
- Malfunction of the control unit (software controller).
- Defective temperature sensor.
- Severe clogging of the filter, resulting in reduced circulation and heat transfer.
-
Cleans dishes poorly
The main reasons why the dishwasher cleans dishes poorly are often due to incorrect use of household appliances, particularly:
- Excessively "hard" water and/or insufficient regeneration salt.
- Insufficient amount of detergent.
- Improper and/or excessive loading of dishes.
- Low water heating temperature setting.
Possible malfunctions of the dishwasher itself:
- Severe clogging of the filter, resulting in poor water circulation and heating.
- Defective hardness sensor.
-
Unusual noises during operation (such as "knocking", "humming", etc.)
The main reasons for the occurrence of unusual noises during the operation of the Miele dishwasher are:
- Improper dish placement (for example, a plate colliding with the sprayer). This is not a technical malfunction - be attentive when loading the dishwasher.
- Wear of pump bearings and/or the electric motor.
- Defect in the motor itself.
- Wear or defect in the drain pump.
Malfunctions that cause unusual noises during the dishwasher's operation require urgent repairs.
-
Leakage
The main reasons for the loss of tightness in Miele dishwashers are:
- Various mechanical defects: wear of seals, door misalignment, defects in the door lock, cracks in hoses and pipes, etc.
- Clogging of the drain pump.
Main repair work:
-
Button and Switch Replacement
(from 900$)
-
Replacement of Filling Valve (Hose)
(from 1200$)
-
Door Lock (Door Closer) Replacement
(from 800$)
-
Drain Hose Replacement
(from 1200$)
-
Pressure Sensor Replacement
(from 1200$)
-
Aquastop System Repair
(from 1600$)
-
Recirculation Pump Replacement
(from 2600$)
-
Heating Element (Tubular Heater) Replacement
(from 1800$)
-
Pump Repair
(from 2200$)
-
Foreign Object Removal
(from 1400$)
-
Control Board Repair
(from 2800$)
-
Module Repair
(40% of the cost of a new one)
Error codes:
-
Main Error Codes of Miele Dishwashers
Error code Cause, troubleshooting F1 Water temperature sensor error (NTC sensor): sensor malfunction or short circuit.
After detecting this fault, heating does not activate, rinse aid is not dispensed, the program is prematurely interrupted with the display of the specified error and audible notification.
To solve the problem (error 01):
- Check the sensor (R30).
- Check the connectors.
- If the fault persists, contact the Miele Service Center. Replacement of the relevant sensor or repair of its connection circuits is required.
F2 Water temperature sensor error (NTC sensor): sensor disconnection (contact opening).
After detecting this fault, heating does not activate, rinse aid is not dispensed, the program is prematurely interrupted with the display of the specified error and audible notification.
To solve the problem (error 02):
- Check the sensor (R30).
- Check the connectors.
- If the fault persists, contact the Miele Service Center. Replacement of the relevant sensor or repair of its connection circuits is required.
F11 Water drainage error: drainage is absent.
To solve the problem (error 11):
- Check the drain hose (possible blockage or kinking).
- Check the drain filter (possible blockage).
- Check the drain pump (possible malfunction of the pump or its power circuits).
- Check the pressure switch.
F12 Water supply error: water supply is absent.
After detecting this fault, the drain pump starts, and the program is prematurely interrupted with the display of the specified error.
To solve the problem (error 12):
- Check the water supply to the dishwasher's inlet (pressure in the pipeline).
- Check the inlet valve.
- Check the water flow sensor.
F13 Water supply error.
Insufficient filling speed is registered within a certain time frame.
After detecting this fault, the drain pump starts, and the program is prematurely interrupted with the display of the specified error.
To solve the problem (error 13):
- Check the water supply to the dishwasher's inlet (possible insufficient pressure in the pipeline).
- Check the inlet valve.
- Check the water flow sensor.
- Check the inlet valve filter (possible blockage).
F14 Water supply error: pressure switch malfunction.
After detecting this fault, the drain pump starts, and the program is prematurely interrupted with the display of the specified error.
To solve the problem (error 14):
- Check the pressure switch.
- Check the operation of the circulation pump (possible malfunction of the pump itself, power circuits, or blockage).
- Check the water flow sensor.
F15 Water supply error.
Registration of hot water supply at the inlet pipe.
F18 Water supply error.
Registration of water supply to the dishwasher when not intended by the current mode.
After detecting this fault, the drain pump starts, and the program is prematurely interrupted with the display of the specified error along with an audible alert.
To solve the problem (error 18):
- Completely disconnect the dishwasher from the power supply for a few minutes, then reconnect.
- Check the inlet valve (possible blockage or malfunction).
F19 Water supply error.
Registration of excessively low water flow or complete absence of water flow.
After detecting this fault, the drain pump starts, and the program is prematurely interrupted with the display of the specified error along with an audible alert.
To solve the problem (error 19):
- Check the rotation possibility of the flow sensor blades (possible obstruction by a foreign object).
- Check the flow sensor (by replacing it with a known working one), as well as its connecting circuits.
F24 Heating error.
Failure of the heating relay is registered.
After detecting this fault, the drain pump starts, and the program is prematurely interrupted with the display of the specified error along with an audible alert.
To solve the problem (error 24):
- Check the heating relay (heater relay), there might be a relay malfunction or defective contacts.
F25 Heating error.
Registration of excessively low heating speed or complete absence of heating.
After detecting this fault, the specified error is displayed at the end of the program.
To solve the problem (error 25):
- Check the heating relay (heater relay).
- Check the heating element (Tubular Electric Heater - TEH).
F26 Heating error.
Registration of excessively high temperature (over 90°C) or nonsensical values from the temperature sensor.
After detecting this fault, the anti-boil protection is triggered: heating is switched off, the drain pump starts, and the program is prematurely interrupted with the display of the specified error along with an audible alert.
To solve the problem (error 26):
- Check the NTC sensor (by replacing it with a known working one).
- Check the heating element (Tubular Electric Heater - TEH).
- Check the control unit's operation (possible malfunction or failure).
F32 Door closure error.
Automatic door closure does not work.
After detecting this fault, the program does not start, and the specified error is displayed.
To solve the problem (error 32):
- Completely disconnect the dishwasher from the power supply for a few minutes, then reconnect.
- Check the door closing sensor.
F33 Door opening error.
The door lock is jammed or faulty.
To solve the problem (error 33):
- Completely disconnect the dishwasher from the power supply for a few minutes, then reconnect.
- Check the door lock (possible mechanical malfunction).
F36 Door switch error.
F40 Control unit error.
After detecting this fault, the drain pump starts, and the program is prematurely interrupted with the display of the specified error.
To solve the problem (error 40):
- Completely disconnect the dishwasher from the power supply for a few minutes, then reconnect.
- Check the controller (control unit).
F42 Power supply error.
Deviation in the frequency of the supply voltage by more than 5Hz is detected.
After detecting this fault, the drain pump starts, and the program is prematurely interrupted with the display of the specified error along with an audible alert.
To solve the problem (error 42):
- Turn off the dishwasher until the power supply returns to normal operation.
F47 Interface BAE/STD communication error.
An error is registered regarding the connection of the display module.
F51 Heating error.
An error is registered regarding the triggering of the water heating relay.
After registering this fault, the drain pump starts, the program is prematurely interrupted with the display of the specified error, and an audible alert.
To solve the problem (error 51):
- Check the heating relay (possible faults in the relay itself or its connecting circuits).
F52 Excessive foaming.
Excessive foam formation is registered.
After registering this fault, the program continues to execute without activating heating. This error will not be displayed on the control panel; instead, it will be stored in the controller's memory and can be read in service mode.
To solve the problem (error 52):
- Reduce the amount of detergent used.
- Check the pressure sensor (possible faults or poor contact; this is the most likely cause even if foam is visually absent).
- Check the heating relay.
- Check the circulation pump (possible faults or clogging resulting in reduced pressure).
F53 Speed sensor error.
To solve the problem (error 53):
- Check the speed sensor (tachogenerator).
- Check the motor (brush wear may be present).
F63 Door lock device error.
To solve the problem (error 63):
- Check the locking device (door closer).
F67 Circulation pump error.
Registers too low pump speeds or complete absence of rotation.
To solve the problem (error 67):
- Check water supply and circulation hoses (possible blockage).
- Check the pump and its power connections.
- Test the control unit (possible malfunction or operation failure).
F68 Circulation pump error.
Registers an error of the circulation pump shutdown: the pump continues to operate after the shutdown command.
To solve the problem (error 68):
- Check the pump's connection to the control unit (communication disruption may be present).
- Check the pump relay (possible malfunction, contacts sticking).
- Test the control unit (possible malfunction or operation failure).
F69 Circulation pump error.
Registers an error in starting the circulation pump.
After registering this fault, the drain pump starts, the program stops prematurely displaying the specified error, and audible notification is triggered.
To solve the problem (error 69):
- Check hoses on the drain line (possible blockage).
- Check if the circulation pump can rotate (possible blockage by a foreign object).
- Check the pump (possible malfunction).
- Check the pressure switch.
- Test the control unit (possible malfunction or operation failure).
F70 WaterProof error.
Registers a water leak (the AquaStop float switch has been activated).
After registering this fault, the leakage protection system activates: the drain pump starts, the program is paused displaying the specified error, and audible notification is triggered.
To solve the problem (error 70):
Turn off the water supply to the dishwasher and disconnect it from the power.
- Check for water in the drip tray (if present, drain it).
- Check the AquaStop float switch (possible malfunction or sticking).
- Inspect the tray's horizon (possible bending or deformation from transport).
- If water is present in the tray, visually inspect connections for tightness and hose integrity.
- Check the pump (seal wear is possible).
F78 Circulation pump error.
Registers insufficient performance of the circulation pump.
To solve the problem (error 78):
- Check hoses on the drain line (possible blockage).
- Check power supply parameters (possible low voltage).
- Check if the circulation pump can rotate (possible blockage of the impeller by a foreign object or pump jamming).
- Check the flow meter.
- Test the control unit (possible malfunction or operation failure).
F79 Circulation pump error.
Registers a flow distributor malfunction.
To solve the problem (error 79):
- Check the flow distributor.
F84 Door lock error.
Registers incorrect positioning of the door lock bolt.
To solve the problem (error 84):
- Check the door lock bolt (possible mechanical failure).
F85 Door lock error.
Registers absence of signal from the locking device.
To solve the problem (error 85):
- Check the lock sensor.
F86 Salt container lid error.
Registers absence of signal from the container lid sensor.
To solve the problem (error 86):
- Check the lid sensor.
F87 Water softener sensor error.
To solve the problem (error 87):
- Check the softener sensor.
F88 Turbidity sensor error.
After registering this fault, the program continues to run. The error won't display on the screen but will be stored in the controller's memory and can be read in service mode.
To solve the problem (error 88):
- Check the condition of the turbidity sensor (possible contamination on the sensor's surface).
- Verify the functionality of the turbidity sensor (possible malfunction of the sensor itself or damage to its connecting circuits).
F91 Load volume control error.
Registers an obviously incorrect value for the loaded dishes' volume.
To solve the problem (error 91):
- Check the load volume sensor.
F102 Smart Home error.
Registers a connection error with the Smart Home system.
To resolve the issue, check the Wi-Fi connection.
F103 Smart Home error.
Registers an equipment compatibility or connection method error.
F170 Entry lock error.
Registers an error in the entry component sensor.
To solve the problem (error 170):
- Check the rinse aid supply.
F171 Entry lock error.
Registers an error in the entry component sensor.
To solve the problem (error 171):
- Check the salt container.
F172, F173 Water consumption error.
To solve the problem (error 172, 173):
- Check the water consumption sensor (by replacing it with a known working one).
F174 Mid spray arm sensor error.
To solve the problem (error 174):
- Check the mid spray arm sensor (by replacing it with a known working one).
F175 Lower spray arm sensor error.
To solve the problem (error 175):
- Check the lower spray arm sensor (by replacing it with a known working one).
F176 Upper spray arm sensor error.
To solve the problem (error 176):
- Check the upper spray arm sensor (by replacing it with a known working one).
F177 Drain line error.
To solve the problem (error 177):
- Check the drain line (possible clogging of the drain filter).
Determine the cause of the breakdown and the full cost of repair:
Question and Answer:
-
Hello. My Miele G6998 SCVi dishwasher shows error code F70. I read that it indicates Aqua-Stop system activation. What should I do? Can I still use the dishwasher?
Error code 70 indeed indicates a sealing issue. The fact of leakage is detected by a float sensor installed in the dishwasher's drip pan.
If you want to address the problem yourself, you'll need to open the dishwasher, visually inspect the drip pan, and if a leak is present, determine the cause and rectify it.
Keep in mind that the Aqua-Stop sensor might trigger due to a stuck float, uneven dishwasher installation, or pan deformation. In any of these cases, a visual diagnosis should suffice.
Other possible reasons for error code 70 could be a malfunctioning sensor or control unit, but these are extremely rare.
-
Hello. My Miele G6990 dishwasher is showing error code F78. What could be the cause and what should I do now?
Error code 78 indicates insufficient performance of the drain pump, which is determined by the flow meter. Possible causes:
- Malfunction of the drain pump itself (seal jamming due to wear).
- Clogging in the drain line.
- Foreign object blocking rotation (there was a case where a piece of "cleaning" salt obstructed the rotation).
- There could also be a malfunction in the flow meter itself.
-
Error F11 (Drain Fault) on Miele dishwasher: causes and solutions?
Error F11 or the service message "Drain Fault" indicates problems with water drainage. The main causes of this issue include:
- Clog in the drain line (drain filter, hose, plumbing). The problem can be solved by clearing the blockage.
- Malfunction or clog in the drain pump. It could also be a blockage in the drain pump caused by a foreign object.
- Faulty pressure switch.
Reviews:
-
Promptly.
Want to share my opinion about this service for repairing Miele appliances.
The dishwasher displayed F78 and had a water intake problem. I thought I could handle it on my own, but I couldn't because I couldn't find the necessary parts. The technician with "skillful hands" and a complete stock of components fixed everything in 2 hours. I cannot but praise for such promptness.
(25.06.2022)Gennady, New York.
-
Thanks to Andrey.
Dishwasher G 5790 had a problem with the electronic control unit, and there was a constant program failure. Senior service engineer Nichipuruk Anton was able to repair our dishwasher within 2 hours.
As I understand it, he is one of the best specialists in this service. If possible, when having an issue with a dishwasher, try to make an appointment with this specialist. Many thanks, we were satisfied with his work.
(08.01.2022)Victoria New York.
-
Thank you.
We brought our G1272 with the F78 error directly to the service and decided with my wife that if the repair is too expensive, we would just buy a new one.
The repair cost was very pleasing because it didn't involve the replacement of expensive parts. The technicians restored the faulty unit and provided a full 6-month warranty.
(15.11.2021)Alex, New York
Any other questions? Order a callback. The response time is less than a minute.